| Peer-Reviewed

Atomic Force Microscopy and Tensile Strength Analyses of Recycled PAN and PET Blends

Received: 16 July 2015     Accepted: 28 July 2015     Published: 2 September 2015
Views:       Downloads:
Abstract

This investigation focuses on blend of recycled polyacrylonitrile fiber with neat polyethylene terephthalate in order to develop a new product and to improve on the properties of PAN/PET blend for possible new application. The micro-structural characterization using AFM shows possibility of blends development. The AFM images revealed an interpenetrating network of phases in the blends. The mechanical properties: modulus and tensile strength of the blended samples improved when compared to the recycled PAN and pure PET samples. This mechanical property improvement is due to a high ratio of PAN in the composition. This also paves way for possible reuse of PAN fibers rather than disposing it as a waste.

Published in International Journal of Environmental Monitoring and Analysis (Volume 3, Issue 5-1)

This article belongs to the Special Issue New Horizons in Environmental Science

DOI 10.11648/j.ijema.s.2015030501.13
Page(s) 17-21
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2015. Published by Science Publishing Group

Keywords

Recycling, Blends, PAN, PET, Impact Test, Characterization

References
[1] Shivashankar M, Mandal B.K 2012 A review on interpenetrating polymer network. International journal of pharmacy and pharmaceutical sciences. ISSN- 0975-1491 Vol. 4, Suppl. 5.
[2] Doulabi A.H, Mequanint K and Mohammadi H, 2014 Blends and Nanocomposite Biomaterials for Articular Cartilage Tissue Engineering. Journal of Materials, Vol.7, pp 5327-5355. doi:10.3390/ma7075327.
[3] Preeti K.S, Satish K.S and Divya D 2011, chitosan-based interpenetrating polymer network (IPN) hydrogels: a potential multicomponent oral drug delivery vehicle. International journal of comprehensive pharmacy. Vol. 8, issue 01, ISSN 0976-8157.
[4] Tirrell, D. A. 1986, Copolymerization. In Encyclopedia of Polymer Science and Engineering; Mark, H. F.; Bikales, N. M.; Overberger, C. G.; Menges, G. Eds.; Wiley-Interscience: New York, Vol. 4, pp. 192-233.
[5] Kim, B. K. Oh, Y. S. Lee, Y. M. Lee K.Y and Soo L. 2005, Modified polyacrylonitrile blends with cellulose acetate: blend properties Journal of Polymer. Vol. 41, pp 385–390.
[6] Cates, D. M. and White, H. J. 1956, Preparation and properties of fibers containing mixed polymers. II. Polyacrylonitrile-cellulose fibers Journal of Polymer Science. Vol. 20, 181- 195.
[7] Pan W, Yang S. L. Jian M.J and Li G. 2005, Electrical and structural analysis of conductive Polyaniline/polyacrylonitrile composites European Polymer Journal. Vol. 41, pp 2127 – 2133.
[8] Taylor M.P 2012 Temperature and strain controlled optimization of stabilization of polyacrylonitrile precursor fibers. Theses and Dissertations- Mechanical Engineering. Paper 4. http://uknowledge.uky.edu/meetds/4.
[9] Peebles Jr L.H, Peters W, Snow A and Peyser P, 1990, on the exotherm of polyacrylonitrile: Pyrolysis of the homopolymer under inert conditions. Carbon. Vol. 28, issue 5, pp.707-715.
[10] Liu Y, Chae H.G and Kumar S, 2010, Stabilization of Gel-Spun Polyacrylonitrile/Carbon Nanotubes Composite Fibers. Part III: Effects of Stabilization Conditions. in School of Polymer, Textile and Fiber Engineering. Georgia Institute of Technology: Atlanta. p. 23.
[11] Yun J-H, Kim B-H, Yang K.S, Bang Y.H, Kim S.R and Woo H-G, 2009, Process Optimization for Preparing High Performance PAN based Carbon Fibers. Bull. Korean Chemical Society Vol.30 Nos:10, pg 2253-2258.
[12] Liu J, Zhou P, Zhang L, Zhaokun M.A, Liang J and Fong H, 2009, Thermo-chemical reactions occurring during the oxidative stabilization of electrospun polyacrylonitrile precursor nanofibers and the resulting structural conversions. Carbon. Vol. 47, issue 4, pp. 1087-1095.
[13] Liu Y, Chae H.G and Kumar S, 2010, Stabilization of Gel-Spun Polyacrylonitrile/Carbon Nanotubes Composite Fibers. Part II: Stabilization Kinetics and Effects of Various Chemical Reactions in School of Polymer,Textile and Fiber Engineering. Georgia Institute of Technology: Atlanta. p. 23.
[14] Yu M, Wang C, Bai Y, Wang Y and Zhou B.O, 2006, Evolution of tension during the thermal stabilization of polyacrylonitrile fibers under different parameters. Journal of Applied Polymer Science. Vol. 102, issue 6, pp. 5500-55.
[15] Bai Y-J, Wang C-G, Lun N, Wang Y-X, Yu M-J and Zhu B.O, 2006, HRTEM microstructures of PAN precursor fibers. Carbon, Vol.44, Nos: 9, pp. 1773-1778.
[16] Rahaman M, Ismail A and Mustafa A, 2007, A review of heat treatment on polyacrylonitrile fiber. Polymer Degradation and Stability. Journal of Atmospheric Environment.Vol.92, Nos:8, pp. 1421-1432.
[17] Wangxi Z, Jie L and Gang W, 2003, Evolution of structure and properties of PAN precursors during their conversion to carbon fibers. Carbon. Vol.41, Nos:14, pp. 2805-2812.
[18] Sanchez-Soto P.J, Aviles M.A, del Rıo J.C, Ginés J.M and Pascual J, 2001, Thermal study of the effect of several solvents on polymerization of acrylonitrile and their subsequent pyrolysis. Journal of Analytical and Applied Pyrolysis. Vol.58: pp. 155-172.
[19] Fei X, Lofgren E.A and Jabarin S.A, 2010, Melting and Crystallization Behaviour of Poly (ethylene terephthalate) and Poly (m-xylylene adipamide) Blends. Journal of Applied Polymer Science, Vol. 118, pp. 2153–2164.
[20] Guerrero C, Lozano T, Gonzalez V and Arroyo E, 2001. Properties and morphology of poly (ethylene terephthalate) and high density polyethylene blends. J. Appl. Polym. Sci., Vol.82, Issue 1, pp. 382-390.
[21] Costache M.C, Heidecker M.J, Manias E and Wilkie C.A, 2006 “Preparation and Characterization of Poly (Ethylene Terephthalate)/Clay Nanocomposites by Melt Blending using Thermally Stable Surfactants”, Polymer Advance Technology, Vol.17, pp. 764-771.
[22] Imai Y, Nishimura S, Abe E, Tateyama H, Abiko A, Aoyama T and Taguchi H, 2002 “High- Modulus Poly (Ethylene Terephthalate)/Expandable Fluorine Mica Nanocomposites with a Novel Reactive Compatibilizer”, Journal of Chemical Materials, Vol.14, pp. 477-479.
[23] Reis J.M.L, Chianelli-Junior R, Cardoso J.L and Marinho F.J.V, 2011 Effect of recycled PET in the fracture mechanics of polymer mortar, Construction and Building Materials. Vol.25, pp. 2799–2804.
[24] Lehmani A, Durand-Vidal S and Turq P, 1998 Surface morphology of Nafion 117 membrane by tapping mode atomic force microscope, Journal of Apply Polymer Science. Vol. 68 pp. 503–508.
[25] Nazzarro M.S, Ramirez-Pastor A.J, Riccardo J.L, Ochoa N.A and Marchese J 1998, Characterization of asymmetric polysulfone membranes by atomic force microscopy, Revista Mexicana de Fisica. Vol. 44 (s1) pp. 58–61.
[26] Singh S, Khulbe K.C, Matsuura T and Ramamurthy P 1998, Membrane characterization by solute transport and atomic force microscopy, Journal of Membrane Science. Vol. 142, pp 111–127.
[27] Bowen W.R, Hital N, Lovitt R.W and Wright C.J 1998, A new technique for membrane characterization: direct measurement of the force of adhesion of a single particle using atomic force microscope, Journal of. Membrane Science. Vol. 139, pp 269–274.
[28] Kim B.K, Oh Y.S, Lee Y.M, Yoon L.K and Lee S, 2000 Modified Polyacrylonitrile blends with cellulose acetate: Blend properties. Journal of polymer Science. Vol. 41, pp. 385–390.
[29] Kim B.K, Oh Y.S, Lee Y.M, Yoon L.K and Lee S, 1994 Journal of Macromolecular Science – Physics B33 issue 2, pp. 243.
[30] Cates D.M, White H.J 1956, Preparation and properties of Fibers containing mixed polymers II. Polyacrylonitrile-Cellulose Fibers journal of polymer science. Vol.20, pp 181-195
Cite This Article
  • APA Style

    T. A. Adegbola, E. R. Sadiku, S. S. Ray. (2015). Atomic Force Microscopy and Tensile Strength Analyses of Recycled PAN and PET Blends. International Journal of Environmental Monitoring and Analysis, 3(5-1), 17-21. https://doi.org/10.11648/j.ijema.s.2015030501.13

    Copy | Download

    ACS Style

    T. A. Adegbola; E. R. Sadiku; S. S. Ray. Atomic Force Microscopy and Tensile Strength Analyses of Recycled PAN and PET Blends. Int. J. Environ. Monit. Anal. 2015, 3(5-1), 17-21. doi: 10.11648/j.ijema.s.2015030501.13

    Copy | Download

    AMA Style

    T. A. Adegbola, E. R. Sadiku, S. S. Ray. Atomic Force Microscopy and Tensile Strength Analyses of Recycled PAN and PET Blends. Int J Environ Monit Anal. 2015;3(5-1):17-21. doi: 10.11648/j.ijema.s.2015030501.13

    Copy | Download

  • @article{10.11648/j.ijema.s.2015030501.13,
      author = {T. A. Adegbola and E. R. Sadiku and S. S. Ray},
      title = {Atomic Force Microscopy and Tensile Strength Analyses of Recycled PAN and PET Blends},
      journal = {International Journal of Environmental Monitoring and Analysis},
      volume = {3},
      number = {5-1},
      pages = {17-21},
      doi = {10.11648/j.ijema.s.2015030501.13},
      url = {https://doi.org/10.11648/j.ijema.s.2015030501.13},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijema.s.2015030501.13},
      abstract = {This investigation focuses on blend of recycled polyacrylonitrile fiber with neat polyethylene terephthalate in order to develop a new product and to improve on the properties of PAN/PET blend for possible new application. The micro-structural characterization using AFM shows possibility of blends development. The AFM images revealed an interpenetrating network of phases in the blends. The mechanical properties: modulus and tensile strength of the blended samples improved when compared to the recycled PAN and pure PET samples. This mechanical property improvement is due to a high ratio of PAN in the composition. This also paves way for possible reuse of PAN fibers rather than disposing it as a waste.},
     year = {2015}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Atomic Force Microscopy and Tensile Strength Analyses of Recycled PAN and PET Blends
    AU  - T. A. Adegbola
    AU  - E. R. Sadiku
    AU  - S. S. Ray
    Y1  - 2015/09/02
    PY  - 2015
    N1  - https://doi.org/10.11648/j.ijema.s.2015030501.13
    DO  - 10.11648/j.ijema.s.2015030501.13
    T2  - International Journal of Environmental Monitoring and Analysis
    JF  - International Journal of Environmental Monitoring and Analysis
    JO  - International Journal of Environmental Monitoring and Analysis
    SP  - 17
    EP  - 21
    PB  - Science Publishing Group
    SN  - 2328-7667
    UR  - https://doi.org/10.11648/j.ijema.s.2015030501.13
    AB  - This investigation focuses on blend of recycled polyacrylonitrile fiber with neat polyethylene terephthalate in order to develop a new product and to improve on the properties of PAN/PET blend for possible new application. The micro-structural characterization using AFM shows possibility of blends development. The AFM images revealed an interpenetrating network of phases in the blends. The mechanical properties: modulus and tensile strength of the blended samples improved when compared to the recycled PAN and pure PET samples. This mechanical property improvement is due to a high ratio of PAN in the composition. This also paves way for possible reuse of PAN fibers rather than disposing it as a waste.
    VL  - 3
    IS  - 5-1
    ER  - 

    Copy | Download

Author Information
  • Department of Mechanical Engineering, Faculty of Engineering and the Built Environment, Tshwane University of Technology, Pretoria, South Africa

  • Department of Chemical Engineering, Faculty of Engineering and the Built Environment, Tshwane University of Technology, Pretoria, South Africa

  • Center for Science and Industrial Research (CSIR), Meiring Naude Road, Brummeria, Pretoria, South Africa

  • Sections